* * * End Of Summer Sale. 10% Off Entire Order * * * Excludes: Transmissions. Combo Kits and Real Deal kits already have 10% off.

Search By Manufacturers

*Speedometer Gears/Speedometer World

 Search by categories
700R4   4L60E   Ratio Adapters   700R4 Gear Driven Electronic   Electronic Ratio Adapter   200-4R
Speedometer Cables   Special Speedo Tail Housings   4L80E   TH350   TH400   Cable X   Super T10   AXOD & E
E4OD   Universal Cable and Pulse Generators   Dodge & Jeep   Ford   Electronic TH400   GM 1964 Back
90 Degree   Miscellanies Gears T5 T10   Ford Manual   Older Ford Gears   Ford Red 18 Tooth, 57-63
GM Only    Ford Only    Dodge / Jeep Only    Cables Only    Housings Only
Ford / Chrysler / VDO Odometer Gears

Speedometer Gears from PATC for Dodge Speedometers, Ford Speedometers and GM Speedometers.  Speedometer Ratio Adapters, Speedometer Cables, Speedometer Housings, Speedometer Clips, Speedometer Retainers, Speedometer O-Rings, Speedometer Speed Sensors & more. 700R4 Speedometers, AOD Speedometers

*** $3.00 USPS US Shipping on Speedometer Parts Under 1 Pound ***

Speedometer Calibration:
Variables such as the vehicle’s axle ratio and tire diameter affect the accuracy of the speedometer. The following speedometer drive gears and driven gears are available for the 700R4 / 4L60 transmissions. Most cars and trucks with low rear end ratios will take a 15 tooth drive gear. There are two driven gear housings, one for 34 through 39 tooth driven gears and one for 40 through 45 tooth driven gears. Look at the bottom of the speedometer face for the numbers 940, 960, 1000, or 1020. These numbers are the number of revolutions the speedometer cable must turn in one mile of travel. Your speedometer may or may not show a number. Most speedometer from 1965 on use 1000.

Twelve speedometer driven gears are available for the 700R4 / 4L60 transmissions to calibrate the speedometer with various axle ratios and tire diameters. The number on the driven gear housing must match the number of teeth on the driven gear. Unless driven gears with more than 45 teeth and / or drive gears with fewer than 15 teeth become available, it will be impossible without using a ratio adapter to have an accurate speedometer with rear end gear ratios lower (higher numerically) than 4.10:1, unless 27 inch or larger tires are installed.

To determine your tires true diameter in relation to determining what speedometer gears you need, measure from the ground up to the center of the axle then multiply by two. The actual run out of the tire can be as much as 2 to 3 inches less than what the circumference of the tire measures. In effect your tire has two diameters.

To determine your rear end ratio, raise both tires off of the ground, turn both tires at the same time one complete turn, at the same time count the turns of the drive shaft, this is your ratio.

700R4   4L60E   Ratio Adapters   700R4 Gear Driven Electronic   Electronic Ratio Adapter   200-4R
Speedometer Cables   Special Speedo Tail Housings   4L80E   TH350   TH400   Cable X   Super T10   AXOD & E
E4OD   Universal Cable and Pulse Generators   Dodge & Jeep   Ford   Electronic TH400   GM 1964 Back
90 Degree   Miscellanies Gears T5 T10   Ford Manual   Older Ford Gears   Ford Red 18 Tooth, 57-63
GM Only    Ford Only    Dodge / Jeep Only    Cables Only    Housings Only    
Ford / Chrysler / VDO Odometer Gears

Main Transmission Website https://transmissioncenter.net

OK

Showing 1–32 of 144 results

Main Menu